Pulsarlube EX

Het automatische elektromechanische smeerapparaat Pulsarlube EX is UL-/ATEX-gecertificeerd.

Ontdek meer over de Pulsarlube EX

Product bestellen

Atex

Speciaal ontworpen voor omgevingen waar ATEX Klasse I, Divisie II, Groep C & D certificaten vereist zijn.

LCD

Easy to program with built-in LCD and simple button controls.

Service Pack

Substantial savings from the use of replaceable grease pouches and battery packs.

Pulsarlube EX Series 125, 250

Het is in de eerste plaats ontworpen om aan de volgende eisen te voldoen: UL79, elektrische pompen voor aardolie-doserende producten, 8e editie ANSI/ISA-12.12.01-2000, niet-ontvlambare elektrische apparatuur voor gebruik in gevaarlijke locaties (Klasse I, Divisie 2, Groep C en D).

De Pulsarlube EX bestaat uit een verticale zelfaanzuigende pomp, een microprocessorregelsysteem en een groot LCD-scherm. Dit product is ideaal voor toepassingen waarbij een aanzienlijke tegendruk in de smeerolieleiding aanwezig is, een nauwkeurige smering vereist is of een wegwerpsmeerapparaat van het gastype niet economisch is.

De circuits en onderdelen van de Pulsarlube EX zijn ontworpen op basis van het energiebeperkingsconcept. De constructie is dan ook vonkvrij, explosieveilig en voorkomt dat een elektrisch apparaat een explosief gas kan ontsteken, ongeacht of het onder normale of bepaalde abnormale omstandigheden werkt.

Product dimensies

  • EX125: Ø91mm(3.60″) x 181mm(7.13″) (H)
  • EX250: Ø91mm(3.60″) x 210mm(8.27″) (H)

Product bestellen

Technische specificaties

Specificatie Waarde
Grease Pouch Capacity 125ml/250ml (replaceable)
Power Supply DC 4.5V Battery Pack
Operating Pressure Max. 15bar (218psi)
Operating Temperature -15˚C~60˚C (5˚F~140˚F)
Dispensing Periods 1, 2, 3, 6, 12 month & H (15 days)
Remote Installation Max. 3m (10ft) with O.D. Ø6 tube (Direct mount is preferable)
Multi-Point Installation N/A
Packaging 10 Units/Case
IP Code IP54
Certifications ATEX, KCs, UL, CE

Productcertificaten

Certificaat Waarde
IP code IP54
ATEX Ⅱ 3 G / Ex nL ⅡB T5
UL Cl.Ⅰ, Div. 2, Gps C, D
KCs Ex nL ⅡB T5
MSHA Approval No. 18-A180003-0
CE / Etc. CE (CoC)

 

Productcertificaten

Certificaat Rating Maximum Surface Temperature Enclosure Protection Indices Classification Of Hazardous Locations Certificate Number
UL Class l Division 2 Groups C.D T6 (85˚C) Cl l Div2 E304815
ATEX Ex nL IIB T5 T5 (100˚C) IP54 Zone2(gas) LCIE 07 ATEX 6100X
KTL Ex nL IIB T5 T5 (100˚C) IP54 12-KB2BO-0279X

The Pulsarlube EX is tested and certified by UL (USA), ATEX(Europe), and KTL(Korea), Refer to the above table when Certification for use in Hazardous Locations should be considered.

 

WARNING

Explosion Hazard – Do not remove or replace batteries unless  power has been disconnected or the area is known to be free of ignitable concentrations of flammable gases or vapors.

This equipment is suitable for use in Class I, Division 2, Groups C and D Hazardous Locations OR non-hazardous locations only.

SUBSTITUTION OF MOTOR AND REED SWITCH MAY IMPAIR SUITABILITY FOR DIVISION 2.

Reference Designation Description Type of Protection
M1 Motor Non-incendive Circuit
SW4 Reed Switch Non-incendive Circuit

Accesoires

 

Directe montage installatie

 

Reducer

Type Waarde
A001 Reducer, 3/8″F X 1/4″M Adaptor (Brass)
A002 Reducer, 3/8″F X 1/8″M Adaptor (Brass)
A003 Reducer, 3/8″F x 1/8″M Adaptor (Steel)

45˚ Elbow

Type Waarde
A023 45° Elbow, 1/4”M X 1/4”F Adaptor (Brass)
A024 45° Elbow, 1/8”M X 1/8”F Adaptor (Brass)

90˚ Elbow

Type Waarde
A019 90° Elbow, 1/4”F X 1/4”F Adaptor (Brass)
A020 90° Elbow, 1/8”F X 1/8”F Adaptor (Brass)
A021 90° Elbow, 1/4”M X 1/4”F Adaptor (Brass)
A022 90° Elbow, 1/8”M X1/8”F Adaptor (Brass)

Socket + Pipe + Reducer

Type Waarde
A011 Socket, 1/4″F x 1/4″F Adaptor (Brass)
A012 Socket, 1/8″F x 1/8″F Adaptor (Brass)

 

A121 Pipe,1/4”M X 1/4”M × 50mm (Steel)
A122 Pipe,1/4”M X 1/4”M × 100mm (Steel)
A123 Pipe,1/4”M X 1/4”M × 150mm (Steel)
A124 Pipe,1/4”M X 1/4”M × 200mm (Steel)

 

A106 Pipe, 1/8″M x 1/8″M x 50mm for divider block (Steel)
A107 Pipe, 1/8″M x 1/8″M x 150mm for divider Pipe, 1/8″M x 1/8″M x 100mm for divider block (Steel)
A108 Pipe, 1/8″M x 1/8″M x 150mm for divider block (Steel)
A109 Pipe, 1/8″M x 1/8″M x 200mm for divider block (Steel)

Single point remote installation

Kit No. 2000RC-1

Type Waarde
A005 Reducer, 1/4″F x 1/8″ M Adaptor (Brass)
B002 Mounting Bracket, “L”Shape
B051 Self Drilling Screw, #8ⅹ20
B057 Washer
A012 Socket, 1/8”F x 1/8”F Adaptor (Brass)
A239 Tube Fitting, Push-In Type, PC8-PT1/8″M
A212-1 Distribution Tubing, O.D. 5/16″(8mm). Urethan Tubing, 3ft Pre-filled with (Grease Type)
A243 Thread Converter, PT1/8″F X NPT1/8″M (Brass)

 

Note : For remote installation using a tube, use an 8mm O.D. (5/16″) tubing pre-filled with the same or compatible grease as the grease contained in the unit. Recommend using under short dispensing period settings due to powerful dispensing pressure.

Comments

  1. All Parts should be assembled tightly with PTFE tape.
  2. For optimal performance with remote installation kits, using an NLGI #1 grade grease is recommended.
  3. If the bearing lube point is NPT, use the thread converter.